Part Number Hot Search : 
5500MYEL CY6214 KDV804S D2204UK TLN212F EL3062 BP354 KBPC251
Product Description
Full Text Search
 

To Download LTC125005 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 LTC1250 Very Low Noise Zero-Drift Bridge Amplifier
FEATURES

DESCRIPTIO
Very Low Noise: 0.75VP-P Typ, 0.1Hz to 10Hz DC to 1Hz Noise Lower Than OP-07 Full Output Swing into 1k Load Offset Voltage: 10V Max Offset Voltage Drift: 50nV/C Max Common Mode Rejection Ratio: 110dB Min Power Supply Rejection Ratio: 115dB Min No External Components Required Pin Compatible with Standard 8-Pin Op Amps Available in Standard 8-Pin Plastic DIP and 8-Pin SO Packages
The LTC(R)1250 is a high performance, very low noise zerodrift operational amplifier. The LTC1250's combination of low front-end noise and DC precision makes it ideal for use with low impedance bridge transducers. The LTC1250 features typical input noise of 0.75VP-P from 0.1Hz to 10Hz, and 0.2VP-P from 0.1Hz to 1Hz. The LTC1250 has DC to 1Hz noise of 0.35VP-P, surpassing that of low noise bipolar parts including the OP-07, OP-77, and LT1012. The LTC1250 uses the industry-standard single op amp pinout, and requires no external components or nulling signals, allowing it to be a plug-in replacement for bipolar op amps. The LTC1250 incorporates an improved output stage capable of driving 4.3V into a 1k load with a single 5V supply; it will swing 4.9V into 5k with 5V supplies. The input common mode range includes ground with single power supply voltages above 12V. Supply current is 3mA with a 5V supply, and overload recovery times from positive and negative saturation are 0.5ms and 1.5ms, respectively. The internal nulling clock is set at 5kHz for optimum low frequency noise and offset drift; no external connections are necessary. The LTC1250 is available in a standard 8-pin plastic DIP and 8-pin SO packages.
APPLICATIO S

Electronic Scales Strain Gauge Amplifiers Thermocouple Amplifiers High Resolution Data Acquisition Low Noise Transducers Instrumentation Amplifiers
, LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 4933642.
TYPICAL APPLICATIO
5V 50 GAIN TRIM
Differential Bridge Amplifier
5V 1000pF
Input Referred Noise 0.1Hz to 10Hz
2 VS = 5V AV = 10k 1
18.2k
V
0.1F
350 STRAIN GAUGE
0
2
- +
7 6 AV = 100
LTC1250 3 4
-1
1000pF -5V
18.2k -5V
1250 TA01
-2
U
0 2 6 4 TIME (s) 8 10
LT1250 TA02
U
U
1250fb
1
LTC1250
ABSOLUTE
AXI U RATI GS
Total Supply Voltage (V + to V -) ............................. 18V Input Voltage ........................ (V + + 0.3V) to (V - - 0.3V) Output Short Circuit Duration ......................... Indefinite Storage Temperature Range ................ - 65C to 150C Lead Temperature (Soldering, 10 sec.)................ 300C
PACKAGE/ORDER I FOR ATIO
TOP VIEW NC 1 -IN 2 +IN 3 V- 4 8 7 6 5 NC V+ OUT NC
ORDER PART NUMBER
TOP VIEW
LTC1250CN8
N8 PACKAGE 8-LEAD PLASTIC DIP
TJMAX = 110C, JA = 130CW J8 PACKAGE 8-LEAD CERAMIC DIP TJMAX = 150C, JA = 100CW (J8)
LTC1250MJ8 LTC1250CJ8
OBSOLETE PACKAGE
Consider the N8 or S8 for Alternative Source
Consult LTC Marketing for parts specified with wider operating temperature ranges.
The denotes the specifications which apply over the full operating temperature range, VIN = 5V, otherwise specifications are at TA = 25C.
SYMBOL PARAMETER VOS Input Offset Voltage VOS Average Input Offset Drift Long Term Offset Drift Input Noise Voltage (Note 3) en in IB IOS CMRR PSRR AVOL Input Noise Current Input Bias Current Input Offset Current Common Mode Rejection Ratio Power Supply Rejection Ratio Large-Signal Voltage Gain Maximum Output Voltage Swing Slew Rate Gain-Bandwidth Product Supply Current CONDITIONS TA = 25C (Note 2) (Note 2) TA = 25C, 0.1Hz to 10Hz TA = 25C, 0.1Hz to 1Hz f = 10Hz TA = 25C (Note 4)
ELECTRICAL CHARACTERISTICS
TA = 25C (Note 4)
SR GBW IS
VCM = - 4V to 3V VS = 2.375V to 8V RL = 10k, VOUT = 4V RL = 1k RL = 100k RL = 10k, CL = 50pF No Load, TA = 25C
2
U
U
W
WW
U
W
(Note 1)
Operating Temperature Range LTC1250M (OBSOLETE) ............ - 55C to 125C LTC1250C .......................................... 0C TO 70C
ORDER PART NUMBER
NC 1 -IN 2 +IN 3 V- 4 8 7 6 5 NC V+ OUT NC
LTC1250CS8
S8 PART MARKING 1250
S8 PACKAGE 8-LEAD PLASTIC SO TJMAX = 110C, JA = 200CW

LTC1250M TYP MAX 5 10 0.01 0.05 50 0.75 1.0 0.2 4.0 50 150 950 100 300 500 110 130 115 130 125 170 4.0 4.3/-4.7 4.92 10 1.5 3.0 4.0 7.0 MIN
MIN
110 115 125 4.0
LTC1250C TYP MAX 5 10 0.01 0.05 50 0.75 1.0 0.2 4.0 50 200 450 100 400 500 130 130 170 4.3 /-4.7 4.95 10 1.5 3.0 4.0 5.0
UNITS V V/C nV/Mo VP-P VP-P fA/Hz pA pA pA pA dB dB dB V V V/s MHz mA mA
1250fb
LTC1250
The denotes the specifications which apply over the full operating temperature range, VIN = 5V, otherwise specifications are at TA
SYMBOL PARAMETER fS VOS VOS en IB IOS Internal Sampling Frequency Input Offset Voltage Average Input Offset Drift Input Noise Voltage (Note 3) Input Bias Current Input Offset Current Maximum Output Voltage Swing Supply Current Sampling Frequency CONDITIONS TA = 25C TA = 25C (Note 2) (Note 2) TA = 25C, 0.1Hz to 10Hz TA = 25C, 0.1Hz to 1Hz TA = 25C (Note 4) TA = 25C (Note 4) RL = 1k RL = 100k TA = 25C TA = 25C MIN LTC1250M TYP MAX 4.75 2 0.01 1.0 0.3 20 40 4.3 4.95 1.8 3 5 0.05 MIN LTC1250C TYP MAX 4.75 2 0.01 1.0 0.3 20 40 4.3 4.95 1.8 3 5 0.05 UNITS kHz V V/C VP-P VP-P pA pA V V mA kHz
ELECTRICAL CHARACTERISTICS
100 200 4.0 2.5
100 200
4.0
IS fS
2.5
Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: These parameters are guaranteed by design. Thermocouple effects preclude measurement of these voltage levels during automated testing. Note 3: 0.1Hz to 10Hz noise is specified DC coupled in a 10s window; 0.1Hz to 1Hz noise is specified in a 100s window with an RC high-pass
filter at 0.1Hz. The LTC1250 is sample tested for noise; for 100% tested parts contact LTC Marketing Dept. Note 4: At T 0C these parameters are guaranteed by design and not tested.
TYPICAL PERFOR A CE CHARACTERISTICS
Input Noise vs Supply Voltage
1.6 TA = 25C 1.4 SUPPLY CURRENT (mA) INPUT NOISE (VP-P) 1.2 1.0 0.8 0.6 0.4 0.1Hz TO 1Hz 0.2 0 4 10 6 8 12 14 TOTAL SUPPLY VOLTAGE, V + TO V - (V) 16 0.5 0 4 0.1Hz TO 10Hz 4.0 TA = 25C 3.5
SAMPLING FREQUENCY (kHz)
UW
1250 G01
Supply Current vs Supply Voltage
6
Sampling Frequency vs Supply Voltage
TA = 25C 5
3.0 2.5 2.0 1.5 1.0
4
3
2
10 6 8 12 14 TOTAL SUPPLY VOLTAGE, V + TO V - (V) 16
4
10 6 8 12 14 TOTAL SUPPLY VOLTAGE, V + TO V - (V)
16
1250 G02
1250 G03
1250fb
3
LTC1250
TYPICAL PERFOR A CE CHARACTERISTICS
Input Noise vs Temperature
1.2 VS = 5V 1.0 0.8 0.1Hz TO 10Hz 0.6 0.4 0.1Hz TO 1Hz 0.2 0 -50 -25
4.0 4.5 VS = 5V
SAMPLING FREQUENCY (kHz)
SUPPLY CURRENT (mA)
INPUT NOISE (VP-P)
50 25 75 0 TEMPERATURE (C)
Voltage Noise vs Frequency
80 70
VOLTAGE NOISE (nV/Hz)
100
VS = 5V RS = 10
GAIN (dB)
50 40 30 20 10 0 1 10 100 1k FREQUENCY (Hz) 10k
1250 G07
60 GAIN 40 20 0 -20 1k 10k VS = 5V OR SINGLE 5V TA = 25C CL = 100pF
PHASE: RL = 100k
60 40
BIAS CURRENT (|pA|)
60
Overload Recovery
8
INPUT (V)
INPUT COMMON MODE RANGE (V)
0.2
0 0
OUTPUT (V)
CMRR (dB)
-5
500s/DIV AV = 100, RL = 100k, CL = 50pF, VS = 5V
4
UW
100
1250 G04
Supply Current vs Temperature
8 7 6 5 4 3 2 1
125
2.0 -50 -25 50 25 0 75 TEMPERATURE (C) 100 125
Sampling Frequency vs Temperature
VS = 5V
3.5
3.0
2.5
0 -50 -25
0
75 50 25 TEMPERATURE (C)
100
150
1250 G05
1250 G06
Gain/Phase vs Frequency
100 80
1000
Bias Current (Magnitude) vs Temperature
VS = 5V
80
PHASE MARGIN (DEG)
100
PHASE: RL = 1k
20 0
100k 1M FREQUENCY (Hz)
-20 10M
1250 G08
10 -50
-25
50 75 0 25 TEMPERATURE (C)
100
125
1250 G09
Common Mode Input Range vs Supply Voltage
140
Common Mode Rejection Ratio vs Frequency
120 100 80 60 40 20 0 VS = 5V VCM = 1VRMS
TA = 25C 6 4 2 0 -2 -4 -6 -8 2 3 5 4 6 SUPPLY VOLTAGE (V) 7 8
1250 G11
1
10
100 1k FREQUENCY (Hz)
10k
100k
1250 G12
1250fb
LTC1250
TYPICAL PERFOR A CE CHARACTERISTICS
Transient Response
10 9 8 VS = 8V
OUTPUT SWING (V)
2V/DIV
OUTPUT SWING (V)
1s/DIV AV = 1, RL = 100k, CL = 50pF, VS = 5V
Output Swing vs Output Current, 5V Supply
5 4 3
OUTPUT VOLTAGE (V)
VS = 5V
5
SHORT-CIRCUIT CURRENT (mA)
2 1 0 -1 -2 -3 -4 -5 0.01 0.1 1 OUTPUT CURRENT (mA) 10
1250 G16
OUTPUT VOLTAGE (V)
TEST CIRCUITS
Offset Test Circuit
100pF
100pF
100k
100k 5V 2 10 3
2 10
- +
7 6 OUTPUT
LTC1250 4 -5V
1250 TC01
UW
Output Swing vs Load Resistance, Dual Supplies
18
Output Voltage Swing vs Load Resistance, Single Supply
16 14 12 VS = 10V 10 8 6 4 VS = 5V V - = GND RL TO GND 0 1 2 345678 LOAD RESISTANCE (k) 9 10 VS = 16V
RL TO GND
7 6 5 4 3 2 1 0 0 1 2 NEGATIVE SWING POSITIVE SWING 345678 LOAD RESISTANCE (k) 9 10 VS = 2.5V VS = 5V
2 0
1250 G14
1250 G15
Output Swing vs Output Current, Single 5V Supply
6 VS = SINGLE 5V
Short-Circuit Current vs Temperature
40 30 20 10 0 -10 -20 -30 VOUT = V + VS = 15V VOUT = V -
4 3 2 1 0 0.01
0.1 1 OUTPUT CURRENT (mA)
10
1250 G17
-40 -50 -25
0
50 25 75 TEMPERATURE (C)
100
125
1250 G18
DC to 10Hz Noise Test Circuit (for DC to 1Hz Multiply All Capacitor Values by 10)
5V
5V 2 6 800k 3
- +
7
-
8 1 800k
0.04F 800k
6
-
1/2 LT1057 7 OUTPUT
LTC1250 3 4 -5V
1/2 LT1057
+4
-5V
5
+
0.02F
0.01F
1250 TC02
1250fb
5
LTC1250
APPLICATI
Input Noise
S I FOR ATIO
The LTC1250, like all CMOS amplifiers, exhibits two types of low frequency noise: thermal noise and 1/f noise. The LTC1250 uses several design modifications to minimize these noise sources. Thermal noise is minimized by raising the gM of the front-end transistors by running them at high bias levels and using large transistor geometries. 1/f noise is combated by optimizing the zero-drift nulling loop to run at twice the 1/f corner frequency, allowing it to reduce the inherently high CMOS 1/f noise to near thermal levels at low frequencies. The resultant noise spectrum is quite low at frequencies below the internal 5kHz clock frequency, approaching the best bipolar op amps at 10Hz and surpassing them below 1Hz (Figure 1). All this is accomplished in an industry-standard pinout; the LTC1250 requires no external capacitors, no nulling or clock signals, and conforms to industry-standard 8-pin DIP and 8-pin SO packages.
80 70 OP-27 OP-07 VS = 5V RS = 10
VOLTAGE NOISE (nV/Hz)
60 50 40 30 20 10 0 0.01 0.1 FREQUENCY (Hz) 1
LTC1250 F01
LTC1250
Figure 1. Voltage Noise vs Frequency
Input Capacitance and Compensation The large input transistors create a parasitic 55pF capacitance from each input to V +. This input capacitance will react with the external feedback resistors to form a pole which can affect amplifier stability. In low gain, high impedance configurations, the pole can land below the unity-gain frequency of the feedback network and degrade phase margin, causing ringing, oscillation, and other unpleasantness. This is true of any op amp, however, the 55pF capacitance at the LTC1250's inputs can affect
6
U
stability with a feedback network impedance as low as 1.9k. This effect can be eliminated by adding a capacitor across the feedback resistor, adding a zero which cancels the input pole (Figure 2). The value of this capacitor should be: CF 55pF AV where AV = closed-loop gain. Note that CF is not dependent on the value of RF. Circuits with higher gain (AV > 50) or low loop impedance should not require CF for stability.
CF RF RIN
W
U
UO
-
LTC1250
CP
+
1250 F02
Figure 2. CF Cancels Phase Shift Due to Parasitic CP
Larger values of CF, commonly used in band-limited DC circuits, may actually increase low frequency noise. The nulling circuitry in the LTC1250 closes a loop that includes the external feedback network during part of its cycle. This loop must settle to its final value within 150s or it will not fully cancel the 1/f noise spectrum and the low frequency noise of the part will rise. If the loop is underdamped (large RF, no CF) it will ring for more than 150s and the noise and offset will suffer. The solution is to add CF as above but beware! Too large a value of CF will overdamp the loop, again preventing it from reaching a final value by the 150s deadline. This condition doesn't affect the LTC1250's offset or output stability, but 1/f noise begins to rise. As a rule of thumb, the RFCF feedback pole should be 7kHz (1/150s, the frequency at which the loop settles) for best 1/f performance; values between 100pF and 500pF work well with feedback resistors below 100k. This ensures adequate gain at 7kHz for the LTC1250 to properly null. High value feedback resistors (above 1M) may require experimentation to find the correct value because parasitics, both in the
1250fb
LTC1250
APPLICATI S I FOR ATIO
LTC1250 and on the PC board, play an increasing role. Low value resistors (below 5k) may not require a capacitor at all. Input Bias Current The inputs of the LTC1250, like all zero-drift op amps, draw only small switching spikes of AC bias current; DC leakage current is negligible except at very high temperatures. The large front-end transistors cause switching spikes 3 to 4 times greater than standard zero-drift op amps: the 50pA bias current spec is still many times better than most bipolar parts. The spikes don't match from one input pin to the other, and are sometimes (but not always) of opposite polarity. As a result, matching the impedances at the inputs (Figure 3) will not cancel the bias current, and may cause additional errors. Don't do it.
RF RIN
-
LTC1250
+
1250 F03
Figure 3. Extra Resistor Will Not Cancel Bias Current Errors
Output Drive The LTC1250 includes an enhanced output stage which provides nearly symmetrical output source/sink currents. This output is capable of swinging a minimum of 4V into a 1k load with 5V supplies, and can sink or source >20mA into low impedance loads. Lightly loaded (RL 100k), the LTC1250 will swing to within millivolts of either rail. In single supply applications, it will typically swing 4.3V into a 1k load with a 5V supply. Minimizing External Errors The input noise, offset voltage, and bias current specs for the LTC1250 are all well below the levels of circuit board parasitics. Thermocouples between the copper pins of the LTC1250 and the tin/lead solder used to connect them can overwhelm the offset voltage of the LTC1250, especially if a soldering iron has been around recently. Note also that
Figure 4. RC Output Pole Limits Bandwidth to 330Hz
1250fb
+
-
U
when the LTC1250's output is heavily loaded, the chip may dissipate substantial power, raising the temperature of the package and aggravating thermocouples at the inputs. Although the LTC1250 will maintain its specified accuracy under these conditions, care must be taken in the layout to prevent or compensate circuit errors. Be especially careful of air currents when measuring low frequency noise; nearby moving objects (like people) can create very large noise peaks with an unshielded circuit board. For more detailed explanations and advice on how to avoid these errors, see the LTC1051/LTC1053 data sheet. Sampling Behavior The LTC1250's zero-drift nulling loop samples the input at 5kHz, allowing it to process signals below 2kHz with no aliasing. Signals above this frequency may show aliasing behavior, although wideband internal circuitry generally keeps errors to a minimum. The output of the LTC1250 will have small spikes at the clock frequency and its harmonics; these will vary in amplitude with different feedback configurations. Low frequency or band-limited systems should not be affected, but systems with higher bandwidth (oversampling A/Ds, for example) may need to filter out these clock artifacts. Output spikes can be minimized with a large feedback capacitor, but this will adversely affect noise performance (see Input Capacitance and Compensation on the previous page). Applications which require spike-free output in addition to minimum noise will need a low-pass filter after the LTC1250; a simple RC will usually do the job (Figure 4). The LTC1051/LTC1053 data sheet includes more information about zero-drift amplifier sampling behavior.
CF RF 47k 0.01 LTC1250
1250 F04
W
U
UO
7
LTC1250
APPLICATI S I FOR ATIO
Single Supply Operation The LTC1250 will operate with single supply voltages as low as 4.5V, and the output swings to within millivolts of either supply when lightly loaded. The input stage will common mode to within 250mV of ground with a single 5V supply, and will common mode to ground with single supplies above 11V. Most bridge transducers bias their inputs above ground when powered from single supplies, allowing them to interface directly to the LTC1250 in single supply applications. Single-ended, ground-referenced signals will need to be level shifted slightly to interface to the LTC1250's inputs. Fault Conditions The LTC1250 is designed to withstand most external fault conditions without latch-up or damage. However, unusu-
8
U
ally severe fault conditions can destroy the part. All pins are protected against faults of 25mA or 5V beyond either supply, whichever comes first. If the external circuitry can exceed these limits, series resistors or voltage clamp diodes should be included to prevent damage. The LTC1250 includes internal protection against ESD damage. All data sheet parameters are maintained to 1kV ESD on any pin; beyond 1kV, the input bias and offset currents will increase, but the remaining specs are unaffected and the part remains functional to 5kV at the input pins and 8kV at the output pin. Extreme ESD conditions should be guarded against by using standard antistatic precautions.
1250fb
W
U
UO
LTC1250 PACKAGE DESCRIPTIO U
(Reference LTC DWG # 05-08-1110)
0.005 (0.127) MIN 0.405 (10.287) MAX 8 7 6 5 0.023 - 0.045 (0.584 - 1.143) HALF LEAD OPTION 0.045 - 0.068 (1.143 - 1.727) FULL LEAD OPTION 0.300 BSC (0.762 BSC) 0.025 (0.635) RAD TYP 1 2 3 0.220 - 0.310 (5.588 - 7.874) 4 0.200 (5.080) MAX 0.015 - 0.060 (0.381 - 1.524) 0 - 15 0.045 - 0.068 (1.143 - 1.727) 0.014 - 0.026 (0.360 - 0.660) NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS. 0.125 3.175 0.100 0.010 MIN (2.540 0.254)
J8 0694
J8 Package 8-Lead CERDIP (Narrow .300 Inch, Hermetic)
CORNER LEADS OPTION (4 PLCS)
0.008 - 0.018 (0.203 - 0.457) 0.385 0.025 (9.779 0.635)
OBSOLETE PACKAGE
1250fb
9
LTC1250 PACKAGE DESCRIPTIO U
N8 Package 8-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510)
.400* (10.160) MAX 8 7 6 5 .255 .015* (6.477 0.381) 1 .300 - .325 (7.620 - 8.255) 2 3 4 .130 .005 (3.302 0.127) .045 - .065 (1.143 - 1.651) .065 (1.651) TYP .120 (3.048) .020 MIN (0.508) MIN .018 .003 (0.457 0.076)
N8 1002
.008 - .015 (0.203 - 0.381) +.035 .325 -.015
(
8.255
+0.889 -0.381
)
.100 (2.54) BSC
INCHES MILLIMETERS *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
NOTE: 1. DIMENSIONS ARE
1250fb
10
LTC1250 PACKAGE DESCRIPTIO U
(Reference LTC DWG # 05-08-1610)
.189 - .197 (4.801 - 5.004) NOTE 3 8 7 6 5 .045 .005 .050 BSC .160 .005 .228 - .244 (5.791 - 6.197) .150 - .157 (3.810 - 3.988) NOTE 3 1 2 3 4 .053 - .069 (1.346 - 1.752) 0- 8 TYP .004 - .010 (0.101 - 0.254) .014 - .019 (0.355 - 0.483) TYP .050 (1.270) BSC
SO8 0303
S8 Package 8-Lead Plastic Small Outline (Narrow .150 Inch)
.245 MIN
.030 .005 TYP RECOMMENDED SOLDER PAD LAYOUT .010 - .020 x 45 (0.254 - 0.508) .008 - .010 (0.203 - 0.254)
.016 - .050 (0.406 - 1.270) NOTE: 1. DIMENSIONS IN
INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
1250fb
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
11
LTC1250
TYPICAL APPLICATI
15V 7.5k 3 3 LM399 4 2 1 2
Reference Buffer
+ -
LTC1250 4
10ppm ERROR AT 15mA 1VP-P OUTPUT NOISE 2.5V/C DRIFT (DUE TO LM399)
RELATED PARTS
PART NUMBER LTC1050/LTC1051/ LTC1053 LTC1150/LTC1151 LTC2050/LTC2051/ LTC2052 LTC2053 LTC2054/LTC2055 LTC6800 DESCRIPTION Single/Dual/Quad Precision Zero-Drift Op Amp Single/Dual 15V Zero-Drift Op Amp Single/Dual/Quad Zero-Drift Op Amp Zero-Drift Instrumentation Amp Single/Dual Zero-Drift Op Amp Rail-to-Rail Input/Output Instrumentation Amp COMMENTS VOS Max = 5V, VSUPPLY Max = 16.5V High Voltage Operation Single Supply 2.7V to =/-5V, SOT-23/MS8/GN16 Package Rail-Rail, MS8, 116dB, Two Resistors Set Gain 150A per Amplifier (Max), SOT-23/MS8 Package Low Cost, Single Supply, MS8, Two Resistors Set Gain
12
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 FAX: (408) 434-0507
UO
7
S
Differential Thermocouple Amplifier
R3 1M 0.1% 5V 2 C1 100pF R1 10k 0.1%
6
- +
7 6 R6 7.5k 1% R7 500 FULL-SCALE TRIM R8 5k 1% 10mV/C VOUT 100mV/C
LTC1250 3
-
TYPE K VCM
1250 TA03
+
R2 10k 0.1% R4 1M 0.1% 5V VIN VOUT R5 3k
4 -5V C2 100pF
LT1025 GND
R9 33k -5V
FOR BEST ACCURACY, THERMOCOUPLE RESISTANCE SHOULD BE LESS THAN 100
1250 TA04
1250fb LT/GP 0205 1K REV B * PRINTED IN USA
www.linear.com
(c) LINEAR TECHNOLOGY CORPORATION 1994


▲Up To Search▲   

 
Price & Availability of LTC125005

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X